Boat Outfitting
Boat Leveler 12″ x 11″ Trim Tab Set
$410.39Features:
Wiring
- Color-coded wiring in 25′ to 40′ lengths with quick connects fittings, meets federal standards for heat, pull and insulation, making installation easy.
Solenoids
- They are custom designed for Insta-Trim Boat Leveler Co., epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating driftback. Barb type hose fittings provide tight, secure connections.
Motor
- A powerhouse with coated wirings and a thermal overload that resists temperature and amperage build-up. 1 3/4" stack windings and top mounting eliminated oil leakage. The motor is mounted with stainless steel nuts and bolts, and is easily disassembled.
Brackets
- Swivel type brackets allow cylinders to be mounted an adjusted to any angle. Knockout pins act as shear pins it tab strikes an object.
Pump
- Designed and engineered exclusively by Instatrim. The built-in bypass is factory set at 400 P.S.I. tolerance held to .00025. Amperage doesn’t exceed 16 because the unit circulates oil, rather than stalling out or trying to pump additional pressure.
Motor Cover
- 4 1/2" D x 6" W x 11"H, high impact ABS plastic cover with a built-in oil reservoir mounts easily with two screws. The filler is located in front. Our cover protects the motor from occasional wash down.
Cylinders
- Impact resistant, fiberglass reinforced nylon cylinders eliminates expansion and resists ultra-violet rays. Two expanding type seals, plus O-ring, eliminates high and low pressure leaks. Barbed cylinder fitting and an inserted tubular rod prevents hose blow-off and breakage.
A stainless steel spring retracts the cylinder when the boat is not in motion.
Trim Tabs
- 12 gauge 304 stainless steel trim tabs are available in standard and custom lengths. They are guaranteed against electrolysis, remaining strong and secure. Insta-Trim’s hinges prevent most spray and can be used for transom or bottom mounting.
Hose
- Designed and manufactured exclusively for Insta-Trim with nylon-reinforced webbing and protective PVC coating. Rated at 2000 lb. burst pressure, 15′ of hose is supplied for your system. Entering the transom 6" above the water line, the hoses are held securely with hose trim.
Stainless steel clamps hold the hose to barb fitting at the solenoid.
Rocker Type Controls
- Mounted on the dash they are easy to operate. 2TP Micro switch with silver contact points adjust the tabs for maximum control and performance.
One pint of Insta-Trim biodegradable transmission oil, funnel and mounting hardware is supplied.
Boat Leveler 18″ x 9″ Trim Tab Set
$433.19Features:
Wiring
- Color-coded wiring in 25′ to 40′ lengths with quick connects fittings, meets federal standards for heat, pull and insulation, making installation easy.
Solenoids
- They are custom designed for Insta-Trim Boat Leveler Co., epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating driftback. Barb type hose fittings provide tight, secure connections.
Motor
- A powerhouse with coated wirings and a thermal overload that resists temperature and amperage build-up. 1 3/4" stack windings and top mounting eliminated oil leakage. The motor is mounted with stainless steel nuts and bolts, and is easily disassembled.
Brackets
- Swivel type brackets allow cylinders to be mounted an adjusted to any angle. Knockout pins act as shear pins it tab strikes an object.
Pump
- Designed and engineered exclusively by Instatrim. The built-in bypass is factory set at 400 P.S.I. tolerance held to .00025. Amperage doesn’t exceed 16 because the unit circulates oil, rather than stalling out or trying to pump additional pressure.
Motor Cover
- 4 1/2" D x 6" W x 11"H, high impact ABS plastic cover with a built-in oil reservoir mounts easily with two screws. The filler is located in front. Our cover protects the motor from occasional wash down.
Cylinders
- Impact resistant, fiberglass reinforced nylon cylinders eliminates expansion and resists ultra-violet rays. Two expanding type seals, plus O-ring, eliminates high and low pressure leaks. Barbed cylinder fitting and an inserted tubular rod prevents hose blow-off and breakage.
A stainless steel spring retracts the cylinder when the boat is not in motion.
Trim Tabs
- 12 gauge 304 stainless steel trim tabs are available in standard and custom lengths. They are guaranteed against electrolysis, remaining strong and secure. Insta-Trim’s hinges prevent most spray and can be used for transom or bottom mounting.
Hose
- Designed and manufactured exclusively for Insta-Trim with nylon-reinforced webbing and protective PVC coating. Rated at 2000 lb. burst pressure, 15′ of hose is supplied for your system. Entering the transom 6" above the water line, the hoses are held securely with hose trim.
Stainless steel clamps hold the hose to barb fitting at the solenoid.
Rocker Type Controls
- Mounted on the dash they are easy to operate. 2TP Micro switch with silver contact points adjust the tabs for maximum control and performance.
One pint of Insta-Trim biodegradable transmission oil, funnel and mounting hardware is supplied.
Boat Leveler 12″ x 9″ Trim Tab Set
$398.99Features:
Wiring
- Color-coded wiring in 25′ to 40′ lengths with quick connects fittings, meets federal standards for heat, pull and insulation, making installation easy.
Solenoids
- They are custom designed for Insta-Trim Boat Leveler Co., epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating driftback. Barb type hose fittings provide tight, secure connections.
Motor
- A powerhouse with coated wirings and a thermal overload that resists temperature and amperage build-up. 1 3/4" stack windings and top mounting eliminated oil leakage. The motor is mounted with stainless steel nuts and bolts, and is easily disassembled.
Brackets
- Swivel type brackets allow cylinders to be mounted an adjusted to any angle. Knockout pins act as shear pins it tab strikes an object.
Pump
- Designed and engineered exclusively by Instatrim. The built-in bypass is factory set at 400 P.S.I. tolerance held to .00025. Amperage doesn’t exceed 16 because the unit circulates oil, rather than stalling out or trying to pump additional pressure.
Motor Cover
- 4 1/2" D x 6" W x 11"H, high impact ABS plastic cover with a built-in oil reservoir mounts easily with two screws. The filler is located in front. Our cover protects the motor from occasional wash down.
Cylinders
- Impact resistant, fiberglass reinforced nylon cylinders eliminates expansion and resists ultra-violet rays. Two expanding type seals, plus O-ring, eliminates high and low pressure leaks. Barbed cylinder fitting and an inserted tubular rod prevents hose blow-off and breakage.
A stainless steel spring retracts the cylinder when the boat is not in motion.
Trim Tabs
- 12 gauge 304 stainless steel trim tabs are available in standard and custom lengths. They are guaranteed against electrolysis, remaining strong and secure. Insta-Trim’s hinges prevent most spray and can be used for transom or bottom mounting.
Hose
- Designed and manufactured exclusively for Insta-Trim with nylon-reinforced webbing and protective PVC coating. Rated at 2000 lb. burst pressure, 15′ of hose is supplied for your system. Entering the transom 6" above the water line, the hoses are held securely with hose trim.
Stainless steel clamps hold the hose to barb fitting at the solenoid.
Rocker Type Controls
- Mounted on the dash they are easy to operate. 2TP Micro switch with silver contact points adjust the tabs for maximum control and performance.
One pint of Insta-Trim biodegradable transmission oil, funnel and mounting hardware is supplied.
Boat Leveler 12″ x 8″ Trim Tab Set
$398.99Features:
Wiring
- Color-coded wiring in 25′ to 40′ lengths with quick connects fittings, meets federal standards for heat, pull and insulation, making installation easy.
Solenoids
- They are custom designed for Insta-Trim Boat Leveler Co., epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating driftback. Barb type hose fittings provide tight, secure connections.
Motor
- A powerhouse with coated wirings and a thermal overload that resists temperature and amperage build-up. 1 3/4" stack windings and top mounting eliminated oil leakage. The motor is mounted with stainless steel nuts and bolts, and is easily disassembled.
Brackets
- Swivel type brackets allow cylinders to be mounted an adjusted to any angle. Knockout pins act as shear pins it tab strikes an object.
Pump
- Designed and engineered exclusively by Instatrim. The built-in bypass is factory set at 400 P.S.I. tolerance held to .00025. Amperage doesn’t exceed 16 because the unit circulates oil, rather than stalling out or trying to pump additional pressure.
Motor Cover
- 4 1/2" D x 6" W x 11"H, high impact ABS plastic cover with a built-in oil reservoir mounts easily with two screws. The filler is located in front. Our cover protects the motor from occasional wash down.
Cylinders
- Impact resistant, fiberglass reinforced nylon cylinders eliminates expansion and resists ultra-violet rays. Two expanding type seals, plus O-ring, eliminates high and low pressure leaks. Barbed cylinder fitting and an inserted tubular rod prevents hose blow-off and breakage.
A stainless steel spring retracts the cylinder when the boat is not in motion.
Trim Tabs
- 12 gauge 304 stainless steel trim tabs are available in standard and custom lengths. They are guaranteed against electrolysis, remaining strong and secure. Insta-Trim’s hinges prevent most spray and can be used for transom or bottom mounting.
Hose
- Designed and manufactured exclusively for Insta-Trim with nylon-reinforced webbing and protective PVC coating. Rated at 2000 lb. burst pressure, 15′ of hose is supplied for your system. Entering the transom 6" above the water line, the hoses are held securely with hose trim.
Stainless steel clamps hold the hose to barb fitting at the solenoid.
Rocker Type Controls
- Mounted on the dash they are easy to operate. 2TP Micro switch with silver contact points adjust the tabs for maximum control and performance.
One pint of Insta-Trim biodegradable transmission oil, funnel and mounting hardware is supplied.
Boat Leveler 10″ x 8″ Trim Tab Set
$450.17Features:
Wiring
- Color-coded wiring in 25′ to 40′ lengths with quick connects fittings, meets federal standards for heat, pull and insulation, making installation easy.
Solenoids
- They are custom designed for Insta-Trim Boat Leveler Co., epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating driftback. Barb type hose fittings provide tight, secure connections.
Motor
- A powerhouse with coated wirings and a thermal overload that resists temperature and amperage build-up. 1 3/4" stack windings and top mounting eliminated oil leakage. The motor is mounted with stainless steel nuts and bolts, and is easily disassembled.
Brackets
- Swivel type brackets allow cylinders to be mounted an adjusted to any angle. Knockout pins act as shear pins it tab strikes an object.
Pump
- Designed and engineered exclusively by Instatrim. The built-in bypass is factory set at 400 P.S.I. tolerance held to .00025. Amperage doesn’t exceed 16 because the unit circulates oil, rather than stalling out or trying to pump additional pressure.
Motor Cover
- 4 1/2" D x 6" W x 11"H, high impact ABS plastic cover with a built-in oil reservoir mounts easily with two screws. The filler is located in front. Our cover protects the motor from occasional wash down.
Cylinders
- Impact resistant, fiberglass reinforced nylon cylinders eliminates expansion and resists ultra-violet rays. Two expanding type seals, plus O-ring, eliminates high and low pressure leaks. Barbed cylinder fitting and an inserted tubular rod prevents hose blow-off and breakage.
A stainless steel spring retracts the cylinder when the boat is not in motion.
Trim Tabs
- 12 gauge 304 stainless steel trim tabs are available in standard and custom lengths. They are guaranteed against electrolysis, remaining strong and secure. Insta-Trim’s hinges prevent most spray and can be used for transom or bottom mounting.
Hose
- Designed and manufactured exclusively for Insta-Trim with nylon-reinforced webbing and protective PVC coating. Rated at 2000 lb. burst pressure, 15′ of hose is supplied for your system. Entering the transom 6" above the water line, the hoses are held securely with hose trim.
Stainless steel clamps hold the hose to barb fitting at the solenoid.
Rocker Type Controls
- Mounted on the dash they are easy to operate. 2TP Micro switch with silver contact points adjust the tabs for maximum control and performance.
One pint of Insta-Trim biodegradable transmission oil, funnel and mounting hardware is supplied.
NavPod PP5061 PowerPod Precut f/Grand Prix Series f/Raymarine C120 & E120 Dash Mount
$453.14| PART #: | |
| Description: | PowerPod, Pre-cut for Raymarine 12″ C120/E120 |
| W x H x D: | 16.625" x 15.125" x 11.25" |
NavPod Protects Your Electronics In Harsh Conditions
PowerPod Grand Prix Series with 20/40 Swivel Base
"PowerPods are simply a better way to mount your Radar/Chartplotter, Fishfinder or GPS. You combine the clean look of flush mounting with the features of a swivel base. Turn the PowerPod to get the best view of your color display. Let your co-pilot enter the waypoints while you steer the boat, then swivel the display back for you to see."
The Latest In Industrial Design
Built to complement the latest marine electronic products.
Double Seal for Watertight Integrity
Outer silicone seal is complemented by an internal seal made of memory resistant urethane foam gasketing that keeps its shape and sealing ability over many years.
Polished Stainless Steel TamperProof Fasteners
Large size and strength with new buttonhead style screws that have deep wrench recesses for better tightening power. UV stable polyurethane washers under each fastener improves sealing and holding power of fasteners and long 6 tamperproof wrench provided for easier assembly.
Pre-Cut Models
Includes all of the necessary parts in order to flush mount the unit Comes with a Flush Mount kit which includes a specific gasket and mounting hardware if not supplied by the manufacturer with the unit.
NavPod Protects Your Electronics In Harsh Conditions
NavPod PP5051 PowerPod Grand Prix Series Precut f/Raymarine C80 & E80
$393.29| PART #: | |
| Description: | PowerPod, Pre-cut for Raymarine 8″ C80/E80 |
| W x H x D: | 15.125" x 13" x 10" |
NavPod Protects Your Electronics In Harsh Conditions
PowerPod Grand Prix Series with 20/40 Swivel Base
"PowerPods are simply a better way to mount your Radar/Chartplotter, Fishfinder or GPS. You combine the clean look of flush mounting with the features of a swivel base. Turn the PowerPod to get the best view of your color display. Let your co-pilot enter the waypoints while you steer the boat, then swivel the display back for you to see."
The Latest In Industrial Design
Built to complement the latest marine electronic products.
Double Seal for Watertight Integrity
Outer silicone seal is complemented by an internal seal made of memory resistant urethane foam gasketing that keeps its shape and sealing ability over many years.
Polished Stainless Steel TamperProof Fasteners
Large size and strength with new buttonhead style screws that have deep wrench recesses for better tightening power. UV stable polyurethane washers under each fastener improves sealing and holding power of fasteners and long 6 tamperproof wrench provided for easier assembly.
Pre-Cut Models
Includes all of the necessary parts in order to flush mount the unit Comes with a Flush Mount kit which includes a specific gasket and mounting hardware if not supplied by the manufacturer with the unit.
NavPod Protects Your Electronics In Harsh Conditions
NavPod PP5050 PowerPod Uncut Grand Prix Series
$367.64| PART #: | |
| Description: | PowerPod, Uncut |
| (usable face = 12.75"w x 8.55"h) | |
| W x H x D: | 15.125" x 13" x 10" |
NavPod Protects Your Electronics In Harsh Conditions
PowerPod Grand Prix Series with 20/40 Swivel Base
PowerPods are simply a better way to mount your Radar/Chartplotter, Fishfinder or GPS. You combine the clean look of flush mounting with the features of a swivel base. Turn the PowerPod to get the best view of your color display. Let your co-pilot enter the waypoints while you steer the boat, then swivel the display back for you to see.
The Latest In Industrial Design
Built to complement the latest marine electronic products.
Double Seal for Watertight Integrity
Outer silicone seal is complemented by an internal seal made of memory resistant urethane foam gasketing that keeps its shape and sealing ability over many years.
Polished Stainless Steel TamperProof Fasteners
Large size and strength with new buttonhead style screws that have deep wrench recesses for better tightening power. UV stable polyurethane washers under each fastener improves sealing and holding power of fasteners and long 6 tamperproof wrench provided for easier assembly.
Pre-Cut Models
Includes all of the necessary parts in order to flush mount the unit Comes with a Flush Mount kit which includes a specific gasket and mounting hardware if not supplied by the manufacturer with the unit.
NavPod GP1061 SailPod Precut f/Raymarine C120, E120 & Simrad NSE12 f/9.5″ Guard
$427.49Pre-cut for Raymarine 12″ C120/E120
Grand Prix series outer silicone seal is complemented by an internal seal made of memory resistant urethane foam gasketing that keeps its shape and sealing ability. Polished stainless steel tamperproof fasteners. NavPod allows you to place your electronics within reach. Dimensions (16.75″w x 13″h x 6.5″d)
NavPod GP1060 SailPod Uncut f/9.5″ Pedestal Guards
$410.39GP1060 Uncut Flush Front
Uncut – Flush Front (usable face = 13.75″w x 10.75″h).
Grand Prix series outer silicone seal is complemented by an internal seal made of memory resistant urethane foam gasketing that keeps its shape and sealing ability. Polished stainless steel tamperproof fasteners. NavPod allows you to place your electronics within reach. Dimensions (16.75″w x 13″h x 6.5″d)
Raymarine Console Mounting Bracket, ST40 Instruments
$40.49Console Mounting Bracket, ST40 Instruments
Aluminum bracket allows for tabletop, console, or overhead mounting of ST40 Instruments
Includes bracket and mounting hardware.
NavPod TP125 Top Plate Adaptor
$145.34| PART #: | |
| Description: | Top Plate Adaptor for 1.25" AngleGuard on Edson Steering System |
| W x H x D: | 9.5" x 9.5" x 1.25" |
NavPod Protects Your Electronics In Harsh Conditions
Top Place Adaptor
NavPod AngleGuards are designed to upgrade sailboat steering systems to accommodate mounting of electronics onto NavPods.
Edson is a popular manufacturer of steering systems who has always used a 9.5" wide pedestal guard. Most of their pedestal guards are 1" in diameter. Lewmar (formally Whitlock) also has manufactured steering systems that use the 9.5" wide format. NavPod supplies the SG10 and AG10 as a easy retrofit onto either of these systems.
Because of the clean and secure method of concealing wires and the need to accommodate large connectors and heavy radar cables within the Stainless Steel tubes, NavPod recommends the larger 1.25" diameter AngleGuards. Often the existing Top Plate needs to be bored out or replaced with the TP125 to accommodate the larger diameter. NavPod supplies Polished Stainless Steel feet with all 1.25" AngleGuards.
NavPod AG126 Pedestal Guard
$282.14AG126 Pedestal Guard
Double Bend AngleGuard 9.5″ Wide 1.25″ for one InstrumentPod and a large GP1030 or GP1060 SailPod below on the angled section. AngleGuards are available in 1” or 1.25” diameter stainless steel tubes.
Features:
- 316 grade stainless steel
- .065 gauge wall thickness
- Mirror polished finish
- All 1.25” include stainless steel feet (1” does not include feet)
NavPod AG226 Pedestal Guard
$282.14AG226 Pedestal Guard
Double Bend AngleGuard 12″ Wide by 1.25″ diameter for one InstrumentPod and a large GP2030 or GP2060 SailPod
Features:
- 316 grade stainless steel
- 065 gauge wall thickness
- Mirror polished finish
- All 1.25” include stainless steel feet (1” does not include feet)
NavPod Stanchion Kit SK135 – For All SailPods & Most SystemPods
$213.74Stanchion Kit SK135 – For All SailPods & Most SystemPods
Great for overhead mounting on Powerboats or extending the available dash space on the flybridge. Useful for unique mounting locations in the cockpit on Sailboats.
Includes two 1.25″ Stainless Steel tubes with 15° bends pre-drilled for mounting 9.5″ or 12″ SailPods or SystemPods on a flat surface (does not fit GP1500/GP2500 Series or GP1600/GP2600 Series SystemPods).
Stanchion Kit includes:
- 1.25″ diameter 316 stainless steel
- Mirror polished finish
- Pre-drilled mounting and wire access holes
- Stainless steel feet can be removed for adjusting the height
Furuno AUMOUNT-2 Mast Mount
$360.24Radome Mast Mount Bracket
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
Poly-Planar Pivot Mount
$22.73Pivot Mount
Part Number: M-1
M1 Pivot Mount brackets are designed to allow maximum mounting versatility for PolyPlanar box speakers (MA-9060, MA-800, MA-7500 and MA-1610) and other popular name box speakers. Since all speakers are directional, M1 brackets allow you to point your speakers in whatever direction produces the best sound quality for the location, whether you’re in a small cabin or on the upper deck of a luxury yacht. The brackets also perform exceptionally well when mounted in marinas, restaurants or backyards.
Features
- Simple mounting that allows you to mount speakers in difficult locations
- Corrosion-proof construction
- They rotate up to 360°
Poly-Planar Stereo Weather Enclosure – White
$43.00Stereo Weather Enclosure – White
Part Number: WC-400W
Install virtually any auto or marine stereo on your boat without fear of damage from moisture, corrosion or UV rays. The WC400 is waterproof housing that surrounds your stereo on all sides for maximum protection. A gasket-sealed, polycarbonate splash cover on the front of the rugged ABS enclosure prevents water from entering. The hinged cover lifts easily and remains out of the way in any of several positions. When open, it maintains partial splash protection while still allowing access to stereo controls. Wires and a rear connector let you hook up the stereo and antenna through the housing. A gimbal mounting bracket permits installation above or below the dash, under an electronic box or on any convenient horizontal surface.
Features
- Accommodates any dual post, removable and DIN-style stereos
- High Impact ABS Housing
- Plastic Bracket
- Dash or Overhead Mounting
- Mounting Hardware Included
- Available in Black or White
Specifications
Overall Dimensions: 4-3⁄16” (H) x 9-1⁄16” (W) x 10-5⁄16” (D)
Furuno Table Top Display Mounting Bracket f/ MU-155C Display
$296.40Display Table Top Mounting Bracket with Knobs and Screws
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
Poly-Planar Radio Splash Panel Mount Cover
$13.87Radio Splash Cover
The gasket-sealed lid on this splash cover prevents water entry into virtually any marine or spa stereo on the market. Accommodates any dual post, removable and DIN-style stereos. Contemporary styling makes it an attractive addition to the dashboard or wall. The lid lifts easily and stays open in multiple positions to maintain partial splash protection while allowing access to radio controls. Stainless steel mounting hardware (included) ensures that corrosion will not damage the mount.